Description
Geekvape Z Coils: Z Series Mesh Coils for Zeus Sub-Ohm Tanks
Geekvape Z coils are GeekVape’s standard Z Series mesh heads – once boxed as Zeus or Mesh Z coils – for the Z sub-ohm tanks that come with the Aegis Legend and Aegis Solo mods. Each pack holds five, and we list the Z0.15, Z0.2, Z0.25 and Z0.4.
They are KA1 (kanthal) mesh coils for direct-to-lung vaping at 45W and up. Further down we compare them with the longer-life Geekvape Z XM coils, which fit the same tanks.
🔌 Geekvape Z Series Coils at a Glance
✔ Five coils per pack
✔ KA1 kanthal mesh
✔ Z0.15, Z0.2, Z0.25 and Z0.4
✔ Lung vaping, 45–90W
✔ Screw-in base
✔ Interchangeable with Z XM coils
Z Coil Resistances and Wattage
The rating is etched on each coil. The Z0.25 is a dual mesh; the others are single mesh. Stock varies by resistance.
| Coil | Resistance | Wattage | Build |
|---|---|---|---|
| Z0.15 | 0.15Ω | See note below | Mesh |
| Z0.2 | 0.2Ω | 70–80W | KA1 single mesh |
| Z0.25 | 0.25Ω | 45–57W | KA1 dual mesh |
| Z0.4 | 0.4Ω | 50–60W | KA1 mesh |
Which Tanks and Kits Take Geekvape Z Coils?
Any GeekVape tank designed for Z coils takes every coil on this page.
GeekVape’s chart for the Aegis L200 Legend 3 kit marks all four standard Z coils compatible with its Z Fli tank. The Aegis Solo 3 kit comes with standard Z coils – a Z0.2 fitted and a Z0.4 spare – and the Aegis Legend 5 kit ships with XM coils, but its Z sub-ohm tank takes these just as well.
All three spare tanks we sell take them too: the flip-top Geekvape Z Fli tank, the child-lock Z Sub-Ohm SE tank and the Z Sub-Ohm Tank 5. So do the Z Sub-ohm 2021 tanks in the older Aegis Legend 2, Solo 2 (S100), Max 2 and T200 kits.
Will not fit: the Z Max tank (M Series coils), the Z Nano 2, Z Nano 3 and Z Nano MTL (B Series coils), or the Obelisk 60, 65 and C. GeekVape also excludes the Z0.25 from the P Subohm tank.
How to Fit and Prime a Geekvape Z Coil
- Empty the tank or turn it upside down, then unscrew the base.
- Remove the old coil and wipe away any liquid.
- Wet the new coil: a drop on top of the cotton and a couple through each side window.
- Fit it flush in the base, reassemble and fill. GeekVape advises three to five minutes’ soak before firing.
How Long Does a Geekvape Z Coil Last?
GeekVape doesn’t publish a figure for the standard Z coils, and we won’t invent one. The lower the resistance and the higher the wattage, the sooner a coil wears: a Z0.15 at 80W goes faster than a Z0.4 at 50W, and sweet, dark e-liquids clog any mesh sooner.
Geekvape Z Coil Troubleshooting
| Problem | Likely cause and fix |
|---|---|
| Dry hit on the first puff | The wick wasn’t wet. Prime the side windows and wait a few minutes. |
| Spitback | Too much liquid in the coil. A few unpowered pulls with the airflow open clears it. |
| Mod says “No atomiser” | Check the coil is screwed into the base and the 510 pin is clean. |
Geekvape Z Coils vs Z XM Coils
| Standard Z coils (this page) | Z XM coils | |
|---|---|---|
| Resistances | Z0.15, Z0.2, Z0.25, Z0.4 | Z0.15 XM, Z0.2 XM, Z0.4 XM |
| Wattage | 45–90W depending on coil | 50–85W depending on coil |
| Mesh | KA1 single mesh (Z0.25: dual) | Denser-centre mesh |
| Life | No official figure | About twice the previous generation (GeekVape) |
| Fits | All Z tanks | All Z tanks |
Because they share a base, you can run either type in the same tank.
Best E-Liquids for Geekvape Z Coils
Z coils are for lung vaping, so think low nicotine and plenty of vapour: a higher-VG shortfill with a nicotine shot at around 3mg. GeekVape’s current advice for the Z XM range is freebase at 3mg or less and no nic salts, and we’d follow the same rule here. Our beginner’s guide to vape coils explains why.
Buy Geekvape Z Coils Near You
Need Geekvape Z coils today? Our Totton vape shop, Hythe vape shop and Holbury vape shop stock GeekVape coils, tanks and kits, and the team can check which resistance suits your device and e-liquid. Not sure which 0.15Ω you have? Bring the old box and we’ll match it. Stock varies by store, so give us a call before you travel. Ordering online instead? See our delivery options.
You May Also Like
Frequently Asked Questions
What are Geekvape Z coils compatible with?
GeekVape’s Z tanks – the Z Fli, Z Subohm, Z Subohm 2021, Z Subohm SE and Z Subohm Tank 5 – plus the Obelisk, Obelisk 120FC, Obelisk 200 and P Subohm.
Are Zeus coils the same as Z coils?
Yes. GeekVape renamed its Zeus coils the Z Series. Older boxes say Mesh Z1 (0.4Ω) and Mesh Z2 (0.2Ω).
What is the difference between the Z0.2 and Z0.25?
The Z0.2 is a single mesh coil for 70–80W. The Z0.25 is a dual mesh coil for 45–57W, so it suits a smaller mod or a cooler vape.
How many coils are in a pack?
Five.
Reviews
There are no reviews yet.