Vaporesso GTi Coils – 5 Pack

Vaporesso GTi Coils: Sub-Ohm Mesh for the iTank 2 and iTank T

Vaporesso GTi coils are the sub-ohm mesh coils for Vaporesso’s iTank 2 and iTank T, and so for the Armour MAX, Armour S and Armour Ultra kits. Vaporesso built the GTi platform specifically for direct-to-lung vaping, with larger airways and even heating. There are five coils in a pack, and we stock the 0.15Ω, 0.2Ω, 0.4Ω and 0.5Ω.

GTi coils run hotter than most: the 0.15Ω goes up to 90W. They are not the same as GTX coils, even though the names are one letter apart. Here’s how to pick a resistance, what to set, and how the two iTanks differ.

GTi Coil Resistances and Wattage

Vaporesso’s figures, which match the ranges printed on the coils. Vaporesso’s two sites disagree slightly on the best setting for the 0.15Ω (80W or 85W); the range is the same.

Which Tanks and Kits Take GTi Coils?

Vaporesso’s GTi coil listing names the iTank 2 and iTank T, and through them the Armour MAX, Armour S and Armour Ultra kits.

The Vaporesso Armour MAX Kit and Vaporesso Armour S Kit both come with the iTank 2, and the Vaporesso Armour Ultra Vape Kit with the iTank T – all three run the full GTi range. The Armour MAX reaches 220W and the Armour S and Ultra 100W, so even the 0.15Ω at 90W is within reach.

Replacing the tank itself? The Vaporesso iTank T is in stock, and the Vaporesso iTank 2 takes the same coils when it’s back. Vaporesso also lists the GEN 200 kits.

Will not fit: GTX devices and pods – the Armour G, Armour GS, Armour G Series pods, GTX One and LUXE XR. Vaporesso says GTi and GTX are separate platforms and not interchangeable.

How to Fit and Prime a GTi Coil

1. Take the iTank off the mod and open it to reach the coil, as shown in the tank’s manual.
2. Pull out the old GTi coil and push the new one in until it’s secure.
3. Wet the cotton through the side ports and add a few drops down the chimney. Vaporesso gives no priming steps, so this is our routine.
4. Reassemble the tank, fill from the top and leave it ten minutes.
5. Start 10W below Vaporesso’s best figure and increase gradually.

How Long Does a GTi Coil Last?

Vaporesso says a GTi coil typically lasts five to six tank refills – one to two weeks for a daily DTL vaper – and that its dual-mesh versions last a little longer. That fits what our Armour customers report. The 0.15Ω at 90W wears fastest; the 0.5Ω goes longest. Replace it when the taste turns dull or burnt.

GTi Coil Troubleshooting

iTank 2 vs iTank T: Both Take GTi

Whichever tank you have, every GTi coil on this page fits it.

Best E-Liquids for GTi Coils

Vaporesso doesn’t give nicotine or VG guidance for GTi coils. For sub-ohm coils running 30–90W, we recommend a 70/30 shortfill at 3mg, or 6mg on the 0.5Ω. Thin 50/50 liquids and nic salts will spit, flood and deliver far too much nicotine at these powers.

Buy Vaporesso GTi Coils Near You

Need Vaporesso GTi coils today? Our Totton vape shop, Hythe vape shop and Holbury vape shop stock Vaporesso coils, tanks and kits, and the team can check which resistance suits your device and e-liquid. We can check whether your tank is GTi or GTX before you buy. Stock varies by store, so give us a call before you travel. Ordering online instead? See our delivery options.

You May Also Like

• Vaporesso GTX Coils
• Vaporesso iTank T
• Vaporesso iTank 2
• All Vaporesso Products

Frequently Asked Questions

What tanks use GTi coils?

The Vaporesso iTank 2 and iTank T, which come with the Armour MAX, Armour S and Armour Ultra kits. Vaporesso also lists the GEN 200 kits.

What is the best GTi coil?

For most people the 0.4Ω at around 55W. The 0.2Ω for more vapour; the 0.5Ω for a cooler, tighter draw.

Are dual mesh GTi coils compatible with my tank?

Yes. Dual mesh is a version of the GTi 0.2Ω and 0.4Ω and fits the same tanks.

Do GTi coils fit GTX devices?

No. The Armour G, Armour GS and GTX One use GTX coils; GTi and GTX don’t swap.