Description
Innokin Zlide Tank: a 2ml Child-Lock Slide-Fill Tank for Z Coils
The Innokin Zlide is a 2ml, 22.7mm tank that takes Innokin’s whole Z coil range. Its trick is the fill: take the mouthpiece off and the top cap slides open; put the mouthpiece back and the cap is locked shut. That’s how Innokin makes it child-resistant.
Air comes in at the base, and Innokin designed it mainly for mouth-to-lung vaping. On the Zlide’s own page it lists the 0.48Ω Plex3D mesh coil at 13–16W, but any Z coil fits, so you can set it up for anything from a tight draw to a looser restricted lung.
🔌 Innokin Zlide Tank at a Glance
✔ 2ml capacity
✔ 22.7mm wide
✔ Slide-open top fill
✔ Child-lock: the mouthpiece locks the cap
✔ Bottom airflow
✔ Takes every Innokin Z coil
Which Z Coil for the Zlide?
Every Z coil fits. These are Innokin’s ratings for the ones we stock; Innokin also makes a 1.0Ω and a 1.6Ω.
| Z coil | Wattage (Innokin) | Draw | Build |
|---|---|---|---|
| 0.3Ω | 30–40W | RDL | Kanthal mesh |
| 0.48Ω | 13–16W | MTL | Plex3D mesh |
| 0.5Ω | 14–19W | MTL | Plexus mesh |
| 0.6Ω | 9–13W | MTL | DuoPrime |
| 0.8Ω | 15–18W | MTL | Kanthal |
| 1.2Ω | 10–14W | MTL | Kanthal |
What Can You Put the Zlide On?
The Zlide has a standard 510 connection and is 22.7mm across, so it suits any 510 mod with room for a 22mm tank. Match the coil to your mod’s power: the Z coils run from 9W up to 40W.
Every coil in our Innokin Z coils range fits the Zlide, and if the glass ever breaks, our Innokin Zlide 2ml glass is the replacement. For a mod to put it on, the Innokin Coolfire Z80 NEX kit runs 6–80W on a single 18650, enough for every Z coil.
How to Fill the Zlide and Change the Coil
- Pull the mouthpiece off: the top cap stays locked until you do.
- Slide the top cap open. Innokin suggests closing the airflow while you fill.
- Fill down the side of the glass, slide the cap shut and refit the mouthpiece.
- To change the coil, empty the tank, unscrew it from the base and swap the Z coil, which pushes in.
- Prime a new coil with a few drops through its side holes, and give it a few minutes before your first puff.
How Long Does the Zlide Last?
The tank itself lasts; the coil is the part you replace. The glass is replaceable too, so a crack doesn’t mean a new tank – our Zlide 2ml glass fits.
Zlide Troubleshooting
| Problem | Likely cause and fix |
|---|---|
| The top cap won’t slide | That’s the child lock. Take the mouthpiece off first. |
| Leaking from the base | The airflow was open while you filled, or the coil isn’t pushed in fully. |
| Burnt taste from a new coil | It wasn’t primed. Prime the next one and wait a few minutes. |
| Draw too loose | Use a higher-resistance MTL coil, such as the 0.8Ω or 1.2Ω. |
Best E-Liquids for the Zlide
Innokin says the Zlide works well with 50/50 and 70/30 e-liquids. On the MTL coils, use nic salts at 10mg or 20mg, or a 50/50 freebase e-liquid. Save the higher-VG liquids for the 0.3Ω.
Buy the Innokin Zlide Near You
Need an Innokin Zlide tank today? Our Totton vape shop, Hythe vape shop and Holbury vape shop stock Innokin tanks, coils and spares, and the team can check which resistance suits your device and e-liquid. We’ll show you the child-lock fill before you buy. Stock varies by store, so give us a call before you travel. Ordering online instead? See our delivery options.
You May Also Like
Frequently Asked Questions
What coils fit the Innokin Zlide?
Every Innokin Z coil. Innokin lists the whole Z coil range for the Zlide.
How do you fill the Zlide?
Take the mouthpiece off, slide the top cap open, fill, then close the cap and refit the mouthpiece to lock it.
Is the Zlide MTL or DTL?
Mainly mouth-to-lung, Innokin says, although the 0.3Ω Z coil gives a looser draw.
What is the capacity of the Zlide?
2ml.
Can I replace the Zlide glass?
Yes. The glass section is replaceable.
Reviews
There are no reviews yet.