Description
OXVA VPRIME 2 Pods: Dual Mesh Cartridges with Boost and Eco
The OXVA VPRIME 2 pods on this page are OXVA’s VPRIME Dual Mesh Cartridge: a side-fill pod with a UNITECH 3.0 dual mesh coil built in, sold two to a pack in 0.4Ω and 0.6Ω. Those are the only two resistances OXVA makes it in. The pod is built around the OXVA VPRIME 2, and it fits the original VPRIME as well.
What sets it apart is how it fires. In the VPRIME 2’s Boost mode both mesh strips heat together, and OXVA says the working resistance drops to roughly half the number on the pod; in Eco only one strip fires. That changes the wattage, the e-liquid and the resistance you should choose, all covered below.
🔌 OXVA VPRIME 2 Dual Mesh Pods
✔ Two pods per pack
✔ UNITECH 3.0 dual mesh coil built in
✔ 0.4Ω and 0.6Ω only
✔ Side fill
✔ Boost and Eco on the VPRIME 2, Boost on the original VPRIME
✔ OXVA quotes up to 120% better leak resistance
VPRIME Dual Mesh Pod Wattage: Boost vs Eco
OXVA publishes a separate wattage band for each mode. Boost runs the pod as a dual mesh coil at about half its printed resistance, which is why those numbers climb so high.
| Pod | Boost (dual mesh) | Eco (single mesh) | Airflow OXVA suggests |
|---|---|---|---|
| 0.4Ω | About 0.2Ω, 40–60W | 0.4Ω, 10–40W | Fully open on Boost, three-quarters on Eco |
| 0.6Ω | About 0.3Ω, 35–50W | 0.6Ω, 10–35W | Three-quarters open on Boost, half on Eco |
Which Devices Do VPRIME Dual Mesh Pods Fit?
OXVA lists the Dual Mesh Cartridge for two devices: the VPRIME 2, where Boost and Eco are both available, and the original VPRIME, where it runs in Boost only.
In the OXVA VPRIME 2 Pod Vape Kit you get the whole pod: switch between Boost and Eco whenever you like, which is exactly what it was designed for. Our OXVA VPRIME 2 review covers the device in depth.
In the original VPRIME by OXVA Pod Vape Kit, OXVA says mode switching isn’t available with this pod: it runs in Boost, with the wattage still adjustable. That makes the 0.6Ω the one to buy for the first VPRIME. If you’d rather stay single mesh on that device, the OXVA VPRIME cartridge is the pod OXVA designed for it.
Will not fit: the XLIM, NeXlim or ONEO ranges. OXVA doesn’t list this pod for any device outside the VPRIME family.
How to Fill a VPRIME Dual Mesh Pod
- Take the pod out of the device.
- Open the fill port on the side of the pod.
- Fill slowly, stopping a little short of the top so there is an air gap.
- Close the port fully and wipe the pod and the contacts on its base.
- Refit the pod. OXVA doesn’t give a soak time, so we suggest waiting a few minutes on a new pod and taking the first puffs in Eco.
How Long Does a Pod Last?
OXVA doesn’t put a number on the life of this pod; it says Eco mode helps extend pod lifespan. That matches what we see in the shop: a pod vaped mostly on Boost, at far higher wattage, wears out sooner than one vaped in Eco, and sweet flavours coat mesh faster. Change the pod when the flavour dulls or turns sharp.
VPRIME Dual Mesh Pod Troubleshooting
| Problem | Likely cause and fix |
|---|---|
| Burning out within days | Usually the 0.4Ω on Boost near the top of its band. Move to the 0.6Ω for Boost, or keep the 0.4Ω in Eco. |
| Harsh hit with nic salts | OXVA lists nic salts for Eco only. Switch to Eco, or use a lower-strength freebase on Boost. |
| No Eco option on the original VPRIME | That’s expected. OXVA says this pod runs in Boost only in the first VPRIME, with the wattage still adjustable. |
| Leaking after a refill | The side port isn’t fully closed, or the pod was filled to the brim. Seal it all the way round and leave a small air gap. |
Dual Mesh Pod vs VPRIME Cartridge
| VPRIME Dual Mesh Cartridge | VPRIME Cartridge | |
|---|---|---|
| Coil | UNITECH 3.0 dual mesh | Unitech 2.0 |
| Resistances | 0.4, 0.6Ω | 0.2, 0.4, 0.6, 0.8Ω |
| Fill | Side | Top |
| In the VPRIME 2 | Boost and Eco | Eco only |
| In the original VPRIME | Boost only | The pod it was designed for |
Both pod types fit both devices; what changes is which modes you get. For the wider single-coil range, see the OXVA VPRIME cartridge.
Best E-Liquids for These Pods
OXVA’s VPRIME 2 guide splits e-liquid by mode. On Boost it recommends high-VG freebase (70% VG): up to 6mg on the 0.4Ω and up to 9mg on the 0.6Ω. Our shortfill e-liquids with a nicotine shot sit comfortably in that range. In Eco, nic salts at 10–20mg suit either pod, and OXVA’s own Ox Passion nic salts are an easy match. Not sure which type you need? Read nic salts vs freebase.
Buy VPRIME 2 Pods Near You
Need VPRIME 2 dual mesh pods today? Our Totton vape shop, Hythe vape shop and Holbury vape shop stock replacement pods, coils and kits, and the team can check which resistance suits your device and e-liquid. Tell us whether you vape on Boost or Eco and we’ll point you to the right resistance. Stock varies by store, so give us a call before you travel. Ordering online instead? See our delivery options.
You May Also Like
- OXVA VPRIME 2 Pod Vape Kit
- OXVA VPRIME 2 Review
- OXVA VPRIME Cartridge
- Ox Passion Nic Salts
- All OXVA Products
Frequently Asked Questions
Which VPRIME 2 pod is best on Boost?
The 0.6Ω. On Boost it runs as a dual mesh at about 0.3Ω and 35–50W, while the 0.4Ω is pushed to 40–60W and wears faster.
Do these pods fit the original VPRIME?
Yes. OXVA lists them for the VPRIME, where they run in Boost only, with the wattage still adjustable.
Can I use nic salts in the VPRIME 2?
Yes, in Eco. OXVA’s guide lists nic salts for single mesh (Eco) only.
Is the VPrime OXVA a good vape device?
It is built for DTL vaping in a pocket-sized body, and the dual mesh pods are what give the VPRIME 2 its Boost and Eco modes. Our OXVA VPRIME 2 review goes through its strengths and weaknesses in detail.
How many pods are in a pack?
Two, both the same resistance.
Reviews
There are no reviews yet.